Edge Impulse Docs

Edge Impulse Documentation

Welcome to the Edge Impulse documentation. You'll find comprehensive guides and documentation to help you start working with Edge Impulse as quickly as possible, as well as support if you get stuck. Let's jump right in!

Sony's Spresense

Sony's Spresense is a small, but powerful development board with a 6 core Cortex-M4F microcontroller and integrated GPS, and a wide variety of add-on modules including an extension board with headphone jack, SD card slot and microphone pins, a camera board, a sensor board with accelerometer, pressure, and geomagnetism sensors, and Wi-Fi board - and it's fully supported by Edge Impulse. You'll be able to sample raw data, build models, and deploy trained machine learning models directly from the studio.

To get started with the Sony Spresense and Edge Impulse you'll need:

In addition you'll want some sensors, these ones are fully supported (note that you can collect data from any sensor on the Spresense with the data forwarder):

The Edge Impulse firmware for this development board is open source and hosted on GitHub: edgeimpulse/firmware-sony-spresense.

The Spresense product family.The Spresense product family.

The Spresense product family.

Installing dependencies

To set this device up in Edge Impulse, you will need to install the following software:

  1. Edge Impulse CLI.
  2. On Linux:
    • GNU Screen: install for example via sudo apt install screen.


Problems installing the CLI?

See the Installation and troubleshooting guide.

Connecting to Edge Impulse

With all the software in place it's time to connect the development board to Edge Impulse.

1. Connect the optional camera, sensor, extension board, Wi-Fi add-ons, and SD card

Spresense main board with attached camera, sensor add-on, Wi-Fi add-on, and extension board.Spresense main board with attached camera, sensor add-on, Wi-Fi add-on, and extension board.

Spresense main board with attached camera, sensor add-on, Wi-Fi add-on, and extension board.

Make sure the SD card is formatted as FAT before inserting it into the Spresense.

2. Connect the development board to your computer

Use a micro-USB cable to connect the main development board (not the extension board) to your computer.

3. Update the bootloader and the firmware

The development board does not come with the right firmware yet. To update the firmware:

  1. Install Python 3.7 or higher.
  2. Download the latest Edge Impulse firmware, and unzip the file.
  3. Open the flash script for your operating system (flash_windows.bat, flash_mac.command or flash_linux.sh) to flash the firmware.
  4. Wait until flashing is complete. The on-board LEDs should stop blinking to indicate that the new firmware is running.

4. Setting keys

From a command prompt or terminal, run:



Mac: Device choice

If you have a choice of serial ports and are not sure which one to use, pick /dev/tty.SLAB_USBtoUART or /dev/cu.usbserial-*

This will start a wizard which will ask you to log in and choose an Edge Impulse project. If you want to switch projects run the command with --clean.

Alternatively, recent versions of Google Chrome and Microsoft Edge can collect data directly from your development board, without the need for the Edge Impulse CLI. See this blog post for more information.

5. Verifying that the device is connected

That's all! Your device is now connected to Edge Impulse. To verify this, go to your Edge Impulse project, and click Devices. The device will be listed here.

Device connected to Edge Impulse.Device connected to Edge Impulse.

Device connected to Edge Impulse.

Next steps: building a machine learning model

With everything set up you can now build your first machine learning model with these tutorials:

Looking to connect different sensors? The Data forwarder lets you easily send data from any sensor into Edge Impulse.


Daemon does not start

If the edge-impulse-daemon or edge-impulse-run-impulse commands do not start it might be because of an error interacting with the SD card or because your board has an old version of the bootloader. To see the debug logs, run:

edge-impulse-run-impulse --raw

And press the RESET button on the board. If you see Welcome to nash you'll need to update the bootloader. To do so:

  1. Install and launch the Arduino IDE.
  2. Go to Preferences and under 'Additional Boards Manager URLs' add https://github.com/sonydevworld/spresense-arduino-compatible/releases/download/generic/package_spresense_index.json (if there's already text in this text box, add a , before adding the new URL).
  3. Then go to Tools > Boards > Board manager, search for 'Spresense' and click Install.
  4. Select the right board via: Tools > Boards > Spresense boards > Spresense.
  5. Select your serial port via: Tools > Port and selecting the serial port for the Spresense board.
  6. Select the Spresense programmer via: Tools > Programmer > Spresense firmware updater.
  7. Update the bootloader via Tools > Burn bootloader.

Then update the firmware again (from step 3: Update the bootloader and the firmware).

Updated 4 months ago

Sony's Spresense

Suggested Edits are limited on API Reference Pages

You can only suggest edits to Markdown body content, but not to the API spec.