Renesas RZ/G2L
The Renesas RZ/G2L is a state-of-the-art general-purpose 64-bit Linux MPU with a dual-core ARM Cortex-A55 processor running at 1.2GHz.
The RZ/G2L EVK consists of a SMARC SOM module and an I/O carrier board that provides a USB serial interface, 2 channel Ethernet interfaces, a camera and an HDMI display interface, in addition to many other interfaces (PMOD, microphone, audio output, etc.). The RZ/G2L EVK can be acquired directly through the Renesas website.
For more technical information about RZ/G2L, please refer to the Renesas RZ/G2L documentation.
Please create an account on Renesas' website to be able to download the packages and files outlined in the subsequent sections.
1. Yocto image preparation/patch/build for G2L
Renesas provides Yocto build system to build all the necessary packages and create the Linux image. In this section, we will build the Linux image with the nodejs/npm packages required by Edge Impulse CLI tools. Renesas requires using the Ubuntu 20.04 Linux distribution to build the Linux image. Please follow instructions provided here to setup your build environment for your G2L yocto build. These instructions will also provide you with the necessary bootloader settings required to boot your G2L from sdcard.
In order to use the Edge Impulse CLI tools, NodeJS v18 needs to be installed into the yocto image that you build. Given the instructions called out here, once the following files are downloaded from Renesas (specific versions specified are required):
... and extracted, you need to download the patch file RZG2L_VLP306u1_switch_to_nodejs_18.17.1.patch and place the patch file into the same directory.
After putting all of these files into a single directory + patch file, you will need to create and patch your G2L yocto build environment as follows (this can be exported into a script that can be run):
You can then invoke your G2L yocto build process via:
Renesas documentation here then shows you different build options + how to flash your compiled images onto your G2L board. Once your build completes, your files that will be used in those subsequent instructions called out here to flash your G2L board can be found here:
Accessing the board using screen
screenThe easiest way is to connect through serial to the RZ/G2L board using the USB mini b port.
After connecting the board with a USB-C cable, please power the board with the red power button.
Please install
screento the host machine and then execute the following command from Linux to access the board:You will see the boot process, then you will be asked to log in:
Log in with username
rootThere is no password
Note that, it should be possible to use an Ethernet cable and log in via SSH if the daemon is installed on the image. However, for simplicity purposes, we do not refer to this one here.
2. Installing Edge Impulse Linux CLI
Once you have logged in to the board, please run the following command to install Edge Impulse Linux CLI
3. Connecting to Edge Impulse
With all software set up, connect your google coral camera to your Renesas board (see 'Next steps' further on this page if you want to connect a different sensor), and run:
This will start a wizard which will ask you to log in and choose an Edge Impulse project. If you want to switch projects run the command with --clean.
4. Verifying that your device is connected
That's all! Your device is now connected to Edge Impulse. To verify this, go to your Edge Impulse project, and click Devices. The device will be listed here.
5. Next steps: building a machine learning model
Currently, all Edge Impulse models can run on the RZ/G2L CPU which is a dedicated Cortex A55. In addition, you can bring your own model to Edge Impulse and use it on the device. However, if you would like to benefit from the DRP-AI hardware acceleration support including higher performance and power efficiency, please use one of the following models:
For object detection:
Yolov5 (v5)
FOMO (Faster objects More Objects)
For Image classification:
MobileNet v1, v2
It supports as well models built within the studio using the available layers on the training page.
Note that, on the training page you have to select the target before starting the training in order to tell the studio that you are training the model for the RZ/G2L. This can be done on the top right in the training page.
If you would like to do object detection with Yolov5 (v5) you need to fix the image resolution in the impulse design to 320x320, otherwise, you might risk that the training fails.
With everything set up you can now build your first machine learning model with these tutorials:
6. EON tuner
If you are interested in using the EON tuner in order to improve the accuracy of the model this is possible only for image classification for now. EON tuner supports for object detection is arriving soon.
If you use the EON tuner with image classification, you need to filter the int8 models since they are not supported by the DRP-AI. Also, you need to filter the grayscale models as well. Note that if you leave the EON tuner page, the filter will reset to the default settings, which means you need to re-filter the above models.
7. Deploying back to the device
To run your impulse locally, just connect to your Renesas RZ/G2L and run:
This will automatically compile your model with full hardware acceleration and download the model to your Renesas board, and then start classifying.
Or you can select the RZ/G2L board from the deployment page, this will download an eim model that you can use with the above runner as follows:
Go to the deployment page and select:
Then run the following on the RZ/G2L:
You will see the model inferencing results in the terminal also we stream the results to the local network. This allows you to see the output of the model in real-time in your web browser. Open the URL shown when you start the runner and you will see both the camera feed and the classification results.
Last updated